LG WT5075 Top-Load Washer Suspension Rod Part Number: Complete Guide

If your LG WT5075 top-load washer is shaking, banging, or walking across the floor during the spin cycle, the suspension rods are likely worn out. These rods (also called shock absorbers) support the wash basket and dampen vibration. Replacing them is a common DIY fix, but first you need the correct part number. This guide covers everything you need to know about the LG WT5075 suspension rod part number, how to confirm compatibility, where to purchase the part, and what to expect during installation.

Understanding LG WT5075 Suspension Rods

The suspension rods in your LG WT5075 washer connect the outer tub to the washer cabinet. Each rod contains a spring and a dampening mechanism that absorbs movement. Over time, these components lose tension or leak fluid, causing excessive vibration. The washer may also make loud thumping noises or shut off mid-cycle due to an unbalanced load.

Common Signs of Worn Suspension Rods

• Excessive shaking or vibrating during spin cycles
• Loud banging or clunking sounds, especially on high-speed spin
• Washer moves or “walks” across the floor
• Clothes come out too wet because the spin couldn’t reach full speed
• Error codes such as UE (unbalanced load) or OF (overflow, though rare)

If you notice any of these, check the suspension rods before replacing more expensive parts.

Identifying the Correct Suspension Rod Part Number

LG assigns specific part numbers for each washer model’s suspension rods. For the LG WT5075 (including sub-models like WT5075CW, WT5075CB, WT5075CS), the official replacement suspension rod assembly part number is 6501KW2002A. This part is a complete rod with spring and damper, sold individually. However, LG also sells a set of four rods under part number 6501KW2002B (sometimes listed as a suspension rod kit).

How to Verify Your Model and Part Number

1. Locate your washer’s model and serial number on the label inside the lid or on the back panel.
2. Confirm your model starts with “WT5075”. Common variations: WT5075CW (white), WT5075CB (black steel), WT5075CS (silver).
3. Check the existing rod for a stamped part number. It often matches 6501KW2002A or 6501KW2002B.
4. Cross-reference with LG’s official parts diagrams or reputable appliance parts websites.

Important: Do not assume all LG washers use the same rod. The WT5075 rods are not interchangeable with other LG models like WT5000 or WT5100. Using incompatible parts can cause damage or improper fit.

Where to Buy the LG WT5075 Suspension Rod

You can purchase the suspension rod(s) from several sources. For fastest service, check local appliance parts stores that carry LG genuine parts. Many independent parts suppliers stock this item. If ordering online, choose a vendor that specializes in appliance parts and lists the part number accurately. Be cautious of generic unbranded rods; they may not perform as well and could void your warranty.

• Local appliance parts distributors – Often have the part in stock or can order it.
• LG authorized parts dealers – Guarantee genuine OEM parts.
• Online appliance parts retailers – Typing the part number 6501KW2002A into a search engine will show multiple options.

When buying, decide whether you need one rod or a full set. If only one rod is broken, you can replace just that one. But because the others have similar wear, many people replace all four at once for balanced performance. The kit (6501KW2002B) usually costs less than four individual rods.

Installation Tips for DIY Replacement

Replacing suspension rods on the LG WT5075 is a straightforward job that most homeowners can handle with basic tools. However, take safety precautions: unplug the washer and disconnect the water hoses before starting.

Tools Needed

• Flathead and Phillips screwdrivers
• Pliers or a socket set (depending on cabinet design)
• A strong helper (the tub is heavy)

Basic Steps (Check YouTube for Model-Specific Videos)

1. Remove the top panel – There are typically two screws at the back. Slide the top panel forward and lift it off.
2. Access the old rods – The rods connect the tub to the cabinet at the four corners. You may need to remove a front cover or control panel for some models.
3. Detach the old rod – Unclip or unscrew the rod from both ends. Note the orientation – the rod has a specific top and bottom.
4. Install the new rod – Secure it in the same orientation. Make sure the clips lock firmly.
5. Repeat for remaining rods – Replace one at a time.
6. Reassemble the washer – Replace all panels and test the washer with a small load.

Warning: The wash basket is heavy. Support the basket when removing rods to avoid strain or injury. If the basket drops suddenly, it can damage the machine or hurt you.

Complete installation instructions are available from LG’s service manual for the WT5075, but the above overview gives you an idea of what’s involved.

Final Recommendation

If you experience vibration issues on your LG WT5075, the suspension rods are a likely culprit. The exact part number you need is 6501KW2002A for one rod or 6501KW2002B for a set of four. Purchase genuine LG parts from a trusted source to ensure durability and correct fit. Replacing the rods is a practical DIY repair that can extend your washer’s life without a costly service call. If you’re unsure about the diagnosis, rule out other causes first (level feet, unbalanced loads, or loose floor boards). But in most cases, new suspension rods will restore smooth operation.